International dt466 service manual free download

International truck Service Manuals — download. Related Posts. Leave a Reply Cancel reply Your email address will not be published.

Copyright Use of materials placed on this site is allowed only if there is an active link to Truckmanualshub. This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Accept Reject Read More.

Disconnect the wiring harness connector from the fuel heater optional. Disconnect two ECM engine connectors. These are the two connectors towards the rear of the ECM. Disconnect the wiring harness connector from the ICP sensor.

Page 6. Release valve cover harness by unclipping from the high-pressure oil manifold. Page Cleaning And Inspection Repair or worn, install new grommets. Install valve cover gasket. Guidelines, page Connect two ECM chassis connectors. Page Injector Wiring Harness 2. Slide ground eyelet over injector shielded ground stud Figure Install nut and tighten. Connect the wiring harness to the CKP sensor. Page Figure Connecting to the block heater sensor optional. Install the block heater cable connections optional.

Connect the wiring harness connector to the MAP sensor. Connect wiring harness connector to the IPR valve solenoid. Connect the wiring harness connector at the EGR Connect the wiring harness connector to the CMP control valve. Connect the wiring harness connector to the ECT sensor. Page Description if necessary and passes through the fuel head and is delivered to each fuel injector. Page Periodic Service 6.

Coat fuel bowl threads and a new O-ring with clean fuel. Page Fuel Filter 7. Torque to the special value Table Page Removal 2. Remove the transfer pump inlet tube assembly. Replace low-pressure fuel supply pump if necessary. Page Discard O-ring seal. Figure Removing the fuel rail plug assembly EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures. Page 7. Remove and discard backup ring and injector inlet seal from injector oil inlet adapters in the high-pressure oil rail.

Page Remove gaskets and discard. Page Installation Fuel inlet port O-ring recess 4. Align injector assembly slot with hold down clamp assembly. Connect each injector harness connector to each injector. Page Tighten bolts to the special torque value EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures. Install a new O-ring seal onto the high-pressure pump assembly before installing EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures.

Page Use one wrench to hold EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures. Page Description Starter location will work only with a tooth ring gear. Standard SAE 2 side mount locations. Page Figure Page Removal 3. Page Flexplate Automatic Transmissions Damage to the rear oil hub off guide pins.

Page Discard oil seal assembly. Figure Drilling holes in the rear oil seal EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures. Page Inspection Place the tip of the dial indicator against the crankshaft pilot. Zero the dial indicator. Flywheel resurfacing information is provided for guidance only. Navistar, Inc. Page Ring Gear Replacement B. Page Rear Oil Seal 2. Page Flywheel Assembly tooth ring gears to the special torque value Table Figure Installing guide pins EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures.

Brake actuator piston locknut 6 sensor Back-up ring 6 EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures. Page Reconditioning page and do steps 4 and 5 for cylinders 2, 4, and 6. Page Bcp Sensor 3. Page M12 Plug Assembly Polished surfaces are acceptable. Figure Rail end plug assembly EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures.

Figure Removing brake actuator piston EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures. Page Installation 6. Coat backup rings and injector oil inlet seals with clean engine oil.

Page 1. Lift high-pressure oil rail up and place on engine. Align injector oil inlet adaptors with injector inlets. Page Electrical Connections rear and clip harness to high-pressure oil rail. Figure Injector electrical connector EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures.

Page Power Steering Pump Guidelines, page and need to be oriented to the 5. Remove gasket and discard. Page 2. Install two power steering pump mounting bolts M10 x 35 and tighten to the special torque value Table Page Terminology Terminology Page EGR cooler or out the exhaust data communication. Page — Sulfur dioxide is caused by intake air to charge air. ECM to a vehicle retarder. Page Valve stem-to-valve guide clearance max. Dt in an international bucket truck runs fine then all of a sudden has no throttle response.

It is written in the language of a mechanic and may include valuable detailed information such as specifications, torques, ranges, etc. So the first steps are simple like checking for obvious problems with the fuel injection and air intake system.

Interstate mcbee new custom built for your engine. International owner manual compiled pdf, doc, ppt compiled documents for international owner manual. Is committed to continuous research and development to improve products and introduce technological advances. International designed these engines to run on high pressure oil to hydraulically actuate each injector electronically by the on board computer which is separate from the fuel system which runs at 75 psi.

CAT C If you have any questions, please contact Lang-Mekra Technical Support. Version: 4. For the most recent version of this manual, visit www. Page 1. International Standard Series. Mirror System Manual Disclaimer: This manual must not be used to repair your Packer. The information in this operator manual will be your guide to operation and operator maintenance for this Part REV.

For the latest version of this manual, contact Air Lift. Performance at or visit www. An Air Lift Performance air management system is highly recommended for this product.

Learn more at air- lift. Hazard notations appear in various locations in